# Difference between revisions of "Brute force attack"

A Brute Force Attack also known as an Exhaustive Search is a method of cracking a password where every possible combination is tried. Because of this, brute force attacks are always successful, however, they usually take so much time, they're not worth using.

A mechanical example of a brute force attack is trying every possible combination on a combination lock. This is a tedious process because, with even a simple combination lock where the dial has only 30 places and the lock uses three numbers, would require 75 hours to check every combination if we assume it takes 10 seconds per attempt.

A similar system is used with password cracking on computers, where you first try password "a," then "b," and on to "z," then "aa," "ab," and so on. The number of passwords you need to try grows exponentially the longer the password gets.

Brute force attacks have legitimate uses, like when you've forgotten your password. However, they're mostly used for nefarious purposes.

## Process

At its most basic level, a brute force attack is a three step process:

3. If the password was not successful, go to step 1.

Step 2 is the most difficult step because many systems purposely make it difficult to automate trying a password to prevent brute force attacks.

## Accelerating the Process

In computer systems, passwords almost always allow the letters a-z, capital A-Z, numbers 0-9, and a host of special characters like !@#\$%^&*. If we assume 100 possible characters, and the password is at most eight characters long, it means we will have to try 100^8 + 1 total passwords (or 10,101,010,101,010,102) to guarantee a match. If we assume our PC can try 1,000,000,000 passwords a second, it will take about 116 days to try every password, and for a nine-character-long password, it would take over 32 years! So, why do password crackers even bother with brute force attacks? Because there are several ways to accelerate the process.

### Trying Common Characters First

Unless the system requires an assortment of characters like a capital letter, number, or symbol, most users don't bother with them. Because of this, a brute force system can be setup to first try passwords made up of just the 26 lowercase letters, and, if that fails, just numbers, then just capital letters. This is often enough to crack a large percentage of password. The remaining passwords will require a brute force including the more complex characters. For just lowercase letters, there are only 217,180,147,159 possible passwords, which, assuming 1,000,000,000 attempts can be made each second, would only take about 4 minutes for an 8-character-long password, and about 1.6 hours for a nine-character-long password.

### Faster and Distributed Hardware

1,000,000,000 passwords-a-second may sound impressive, but government or university super computers have also been used for the task which are thousands of times faster. Even smaller groups or individuals can build hardware consisting of dozens of processors chained together, or just use a network of regular computers each running a chunk of the passwords to out pace any single CPU.

## Defenses

There are several ways to protect against or slow down brute force attacks.

It's possible to control the log in process even when it's not running on your PC. If a proprietary software package is built around encryption, the delay can be added to the program itself. Then, even if the file is copied, the cracker would still have to use the same program to decrypt it, which foils brute force attacks. In order to avoid the delay, the cracker would have to reverse engineer the program and recreate it without the delay, which is a tedious and complex process.

Since brute force attacks take exponentially longer to perform as the length of a password increases, each character you add to your password makes it vastly more secure from this type of attack.

### Complex Characters

To prevent a simple brute force of just characters, it helps more than just lowercase letters in your passwords. Adding a symbol will make your password far less susceptible to brute force attacks. In particular, it helps to use a character not found on a keyboard, which many brute force attacks don't even bother with. These are not possible in many older systems, but most new systems allow them. To enter such a character, hold ALT on your keyboard, then type a number on the keypad (the numbers on the side not the top) and release ALT. For example, ALT+236 gives the character "∞" which will be given far less priority in a brute force attack.

For many types of cryptography, the key is encrypted with the data, which means that the correct password can be verified. However, there are some types of encryption which do not store the key at all (like a One-Time Pad), so the only way to know if the password was correct is to look at the data and see if it contains what you are looking for. This process makes brute force attacks useless.

## Program

The following FreeBASIC program will perform a brute force attack on the specified password.

```' This program will run a brute force attack against the specified password string.
' It will try all printable ASCII characters (32-126), but can be easily modified to use a full 256 set.
' This code is for demonstration purposes only, it has not been optimized, and runs extremely slow.

Declare Function GetAttempt As String

Dim As Integer iCount, iRefresh

iRefresh = 15577                                ' Adjust for often you want the screen to refresh. Try to get about 1 refresh a second.
iMaxPasswordLengthAttempt = 20                  ' How many places to try before giving up.

Dim Shared As Integer iAttempt(1 To iMaxPasswordLengthAttempt)
Dim Shared As Integer iAttemptLength = 1
Dim Shared dStart As Double

dStart = Timer

' Trap for an empty password.
Print "Password is blank, instant match!"
Sleep: End
Else
iAttempt(1) = 32
End If

Locate 1, 1: Print "Attemping: "
Do
' Get the current password attempt.
sTry = GetAttempt()

iCount = iCount + 1
If iCount = iRefresh Then
iCount = 0
Locate 1, 12: Print sTry
End If

' Try the current password attempt.
CLS
Print "Found!"
Print "Password is '" + sTry + "'"
Print "After"; (Timer - dStart); " second(s)."
Sleep: End
End If

Loop Until Inkey\$ = Chr(27)

' Convert the array into a simple string for comparison purposes.
Function GetAttempt As String
Dim As Integer I
Dim As String sAttempt

For I = 1 To UBound(iAttempt)
If iAttempt(I) = 0 Then
Exit For
End If

sAttempt = sAttempt + Chr(iAttempt(I))
Next I

Return sAttempt
End Function

' Use itertation to roll the password forward.
' Increment the current place holder.
iAttempt(iPlace) = iAttempt(iPlace) + 1

' Check to see if we need to roll.
If iAttempt(iPlace) = 127 Then
iAttempt(iPlace) = 32

If iPlace = 1 Then
' We've rolled the first place holder, increment the length of the password attempt.
iAttemptLength = iAttemptLength + 1
If iAttemptLength > UBound(iAttempt) Then
' We've reached the end.
CLS
Print "Attemped every password, still no match."
Print "After "; (Timer - dStart); " second(s)."
Sleep: End
End If

iAttempt(iAttemptLength) = 32
Else
' Set the current place to the beginning, and increment the previous